Protective Packaging

Packaging for Heavy Items: Boards, Restraint and Pallet Builds

11 min read 22 Nov 2026 WSUK Team
Triple wall corrugated case holding a heavy steel component, strapped to a wooden pallet with PET strapping and cardboard corner boards in a warehouse
The quick answer

Packaging for heavy items is specified around the weight above the pack and the movement inside it, not around cushioning. Choose board by stack load, usually double wall BC flute or triple wall, restrain the item so it cannot shift, secure it to the pallet with PET strapping and edge protection, and mark the weight and orientation clearly.

When a heavy item stops being a parcel

A 4 kg kettle and a 40 kg gearbox can fit the same size of carton, but they are not the same packaging problem. Weight changes almost every decision in the pack: the board, the foam, how the item is held in place and, before any of that, whether it should be travelling through a parcel network at all.

Parcel networks are built around items one person can lift, sorted on conveyors and loaded by hand. Every carrier sets its own weight and size limits, and they change, so work from your carrier's current terms. The more useful test is practical. As an item gets heavier, surcharges climb, the chance of a drop from a conveyor or tail lift grows, and the packaging needed to survive that handling gets heavier and dearer itself. Somewhere before the carrier's hard limit, protecting a heavy item for a parcel journey costs more than putting it on a pallet.

A pallet journey is a different environment. The item is moved by forklift rather than by hand, it is not thrown, and the main forces come from braking, cornering and whatever is stacked above it. Heavy goods forced into a parcel specification often end up over-packed and under-protected at the same time, and pallet transport and distribution is frequently the cheaper route once the packaging is costed properly.

Choosing board for the weight above it

Board is specified against stack load, not contents. In a warehouse or on a pallet it is the weight above a carton that crushes it, and heavy goods tend to be stacked heavily. A 25 kg carton with three identical cartons on top is carrying 75 kg on its top panel and walls for the whole journey, on top of holding its own contents.

Single wall suits light to medium goods with nothing heavy above. When cartons arrive crushed rather than punctured, the stack has outgrown it. Double wall, usually BC flute at around 6 to 7 mm, is the normal step up for heavy goods and palletised loads. Triple wall, at 14 mm and above, is used for engineering components, machinery parts and export loads. Either should be specified by burst and edge crush resistance against the real weight and journey, which is how heavy-duty industrial packaging is specified, not chosen because it looks strong.

Load situationTypical boardWhat it is resisting
Heavy single carton, parcel or courier journey, nothing stacked aboveDouble wallPuncture, corner knocks and drops in handling
Heavy cartons palletised and stacked several highDouble wall, BC flute (6 to 7 mm)Compression on the bottom layers for the whole journey
Machinery parts, castings and engineering componentsTriple wall, AAA or BAA (14 mm and above)High compression and burst; often replaces a timber case
Very heavy point loads, or goods lifted by crane or slingTriple wall pallet box or timber case, specified to the loadConcentrated loads the board may not carry on its own

Triple wall is often lighter and cheaper than a timber case for goods that do not genuinely need timber. Where an item sits on small feet or has to be slung, timber may still be right, and that is better said at specification than after a failure.

Restraint matters more than cushioning

The commonest mistake with heavy goods is treating them as fragile ones. More bubble wrap round a 30 kg casting achieves very little, because a heavy item that can move inside its pack generates far more force than a drop does. It shifts under braking, hits the carton wall and takes out a corner. The answer is restraint: stopping the item moving at all.

That means fitted parts rather than loose fill. Corrugated fitments and partitions locate the item, foam blocks hold it at points that can bear load, and on a pallet the item may be bolted or strapped to the base. Under a heavy item, void fill compresses and the gap reopens. Protective packaging is specified the same way, against the actual failure mode rather than by adding more of the wrong material.

Foam density for heavy items

Where foam is used, density decides the outcome, not thickness. Closed-cell polyethylene foam, typically 24 to 45 kg/m³, is the usual choice for heavier items and repeat handling; cross-linked PE at 28 to 60 kg/m³ suits fine finishes and fitted trays. Open-cell polyurethane, at 20 to 30 kg/m³, is for light, delicate items and bottoms out under weight. A grade that works at 5 kg protects nothing at 50 kg, which is why foam packaging is specified against product weight and drop height. Bearing area matters as much as grade: a small block under a point load crushes, so inserts for heavy items support the product at strong points such as a flange or base plate.

Strapping, edge protection and stretch wrap

Once an item is on a pallet, load security takes over from cushioning. Polyester (PET) strapping is the usual choice for heavy and settling loads: 12 mm PET typically has a breaking strain of 300 to 450 kg and 19 mm 650 to 900 kg, against 180 to 320 kg for 15 and 19 mm hand polypropylene. PET keeps its tension as a load settles and replaces steel on most loads. Specify by breaking strain rather than width, and remember the joint is where strapping fails; our guide to polypropylene, PET and steel strapping goes further.

Corner boards stop the strap cutting into the cartons, spreading the tension and keeping the load square; without them, a well-strapped pallet of heavy cartons often arrives with every top corner crushed. Stretch film then unitises the load so it behaves as one object.

Building the pallet: base, footprint and unit load

The pallet is part of the packaging. A heavy load needs a sound base rated for it, with deck boards that will not split under a concentrated load. The UK standard pallet is 1200 x 1000 mm and the Euro pallet 1200 x 800 mm; either way, the load should sit within the footprint. Overhang puts weight onto unsupported carton edges, and a small load on a large pallet leaves room to shift.

Heaviest goods go at the bottom, with the centre of gravity low and central. Cartons stacked in columns carry more than cartons interlocked like brickwork, because their walls line up and carry the load straight down. Anti-slip sheets stop a layer walking off, and a single heavy item should be fixed to the base, not just placed on it. Hauliers and pallet networks set their own weight and height limits, so confirm them before the pallet is built. More on keeping loads square is in our piece on corner boards, edge protection and pallet stability.

For heavy goods the order of questions is the weight above, the movement inside, then security on the pallet. Cushioning comes last.

Weight and handling marks

Labelling belongs in the specification, not at the end of the packing line. Whoever moves the pack next needs to know how heavy it is, which way up it travels and where it can be lifted. A gross weight mark lets the receiving site plan the handling, and orientation arrows matter more as items get heavier and less symmetrical.

Mark an off-centre centre of gravity so a forklift driver does not lift from the wrong side, and make fork entry points, lifting points and any do not stack mark visible from more than one side. Hazard marks and carrier or mode rules are a separate matter, confirmed for the specific product rather than assumed.

Get heavy goods packaging specified

Tell us the weight, dimensions, how the item travels and what is stacked above it. We specify the board, restraint and load security together and quote against that specification.

Frequently asked questions

What is the best packaging for heavy items?

No single material. Heavy items need board specified for the stack load, usually double or triple wall, fitted restraint that stops the item moving, and PET strapping with edge protection once palletised, all specified against the weight and journey.

When should a heavy item go on a pallet instead of as a parcel?

When protecting it for rough parcel handling, plus weight surcharges, costs more than a pallet journey, or when it nears your carrier's weight or size limit. Limits vary by carrier, so check current terms.

Can triple wall board replace a timber case?

Often, yes. Triple wall cases are widely used for engineering components and export loads and are frequently lighter and cheaper than timber. Very heavy point loads or crane-lifted goods may still need timber.

What foam density should I use for heavy products?

Closed-cell polyethylene, typically 24 to 45 kg/m³, or cross-linked PE at 28 to 60 kg/m³ for fine finishes. Open-cell polyurethane is for light, delicate goods. Specify against product weight and bearing area.

What markings should a heavy package carry?

The gross weight and orientation arrows as a minimum, plus a centre of gravity mark if the weight is off-centre, clear fork or lifting points, and do not stack where the load cannot carry weight above it.

Related Articles

Freight
Choosing the Right Freight Mode: A Framework for UK Shippers
Air, sea or road? A practical decision framework for balancing cost, speed and reliability.
Freight
FCL vs LCL: Which Container Shipping Option Saves You Money?
Full vs shared containers explained — the break-even point most importers get wrong.
Freight
Road Freight to Europe: What UK Exporters Need to Know
Customs, documentation and transit times for post-Brexit European road freight.

Get a Packaging Quote

Tell us what you pack, how it travels and roughly what volumes, and we will specify it and quote against that specification.