Fulfilment Packaging

Packaging Standardisation: How to Cut Down a Box Range

13 min read 22 Nov 2026 WSUK Team
Pack bench with a short row of corrugated boxes in graded sizes arranged smallest to largest, with a paper void fill dispenser and a tape gun beside them
The quick answer

Packaging standardisation means covering your orders with the fewest box sizes and consumables that still fit them properly. Start from order and dimension data, group the orders into clusters, build a box ladder around them, price what each removed size costs in void fill and volumetric carriage, then consolidate tape, fill and film and measure the result.

Box ranges are usually reviewed one size at a time, which is why they only ever grow. Each addition makes sense on the day: a new product that did not quite fit, a customer whose goods arrived scuffed, a supplier whose medium box was a few millimetres shorter than the last one. Standardisation looks at the whole range at once and asks which sizes the order profile actually needs.

What standardisation is for, and what it costs

The aim is not the shortest possible list. Every size you remove sends its orders into the next size up, carrying more air, more void fill and, on a parcel network, more volumetric weight. Every size you keep has to be bought, stored, replenished and found at the bench. A good range sits where those pressures balance, judged on delivered cost rather than line count. Range length moves all six cost areas in the WSUK Packaging Guide:

Cost areaFewer sizesMore sizes
MaterialsBetter run economics, more board per orderMore lines bought at minimum order quantity
StorageFewer part-used pallets of boardMore racking and slow movers
TransportMore orders charged on airTighter fit, lower volumetric weight
LabourQuicker box choice, fewer wrong-box picksMore decisions, less fill to add
DamageMore movement if fill is skimpedBetter fit, less movement
WasteMore fill per orderLess fill and board per order

Too long a range shows up as part-pallets of board that never run out and packers walking past the right box. Too short shows up as rising void fill use, a carrier bill above expectation and products moving inside the box. That is why standardisation belongs inside a wider packaging review and cost reduction exercise, where all six are examined together.

Start with orders and dimensions, not the stockroom

The stock list tells you what you have bought, not what your orders need. Start from three data sets.

  • Order lines for a representative period including a peak. Multi-item orders matter, because they decide the upper steps.
  • Product dimensions and weights with the protection each product needs on every face, giving a required internal size, as in our guide to choosing the right carton size.
  • Current box usage by size, from purchasing records or, better, from the pack station.

Add the carrier bands you use and, for B2B lines, whether the box travels on a pallet. Do not wait for perfect data: measure the products behind most orders first, because the long tail seldom changes the answer.

Then work out a required size for every order: product plus protection for single items, the combined packed footprint and depth for multi-item orders. That list of what each order needed, independent of the box it went in, is the raw material for everything that follows.

Cluster the orders and find the redundant sizes

Group required sizes by shape before volume. Two orders of similar volume can need completely different boxes if one is long and thin and the other near a cube, so sort into families first: flat, cube-like, long and awkward. Within each, sort by longest side and look for clusters.

Then assign each order to the smallest current box it fits, and count. Three patterns usually appear.

  • Near-duplicates: sizes a few millimetres apart doing the same job, often from different suppliers. One can usually go at no measurable cost.
  • Orphans: sizes very few orders need, kept because one product once did.
  • Gaps: clusters forced into a much larger box because nothing sits between two steps. A gap is a reason to add or move a size.

Standardisation is not only cutting. The best results usually lose several sizes and move one or two to where the orders actually cluster.

Build the ladder and price each removal

Build the box ladder from the bottom up, with steps close together where order volume is dense and further apart where it is thin. Then test every candidate removal on its own numbers:

  1. List the orders that use the size and the step they would move up to.
  2. Work out the extra volume per order and whether the new external size crosses a carrier band.
  3. Add the extra void fill and any extra pack time.
  4. Multiply by annual orders and compare with what the size costs to keep: stock, storage, a bench slot and a minimum order quantity.

As a hypothetical example, take a 300 x 200 x 150 mm box, about 9 litres, whose orders would move to a 350 x 250 x 200 mm box, about 17.5 litres. Each order now ships in nearly twice the volume, so wherever a carrier charges on volumetric weight that weight roughly doubles too, whatever the divisor, and the extra space has to be filled. On a high-volume size that cost repeats on every parcel and usually outweighs the cost of stocking the line. On a size used a handful of times a month, the same arithmetic often says remove it.

The test also works in reverse. Where a high-volume line sits awkwardly between steps, a made-to-size carton can earn a place, compared with the stock box plus the fill, pack time and carrier band it needs rather than the stock box alone.

Parcel despatch rewards a tighter ladder, because a few millimetres can move every order in a step into the next carrier band. Pallet despatch usually tolerates fewer, sturdier sizes chosen for footprint and stack load. If you run both, treat them as two ladders.

The right number of box sizes is the one with the lowest delivered cost against your real orders, which is rarely the smallest number you could get away with.

Consolidate tape, fill and film at the same time

The habits that add a box size also add a tape, a fill and a film.

  • Tape. The common trade range runs from 28 micron polypropylene for general ambient despatch to 38 micron for heavier cartons, with vinyl for cold store and recycled board. Most benches need one general grade plus a specified exception, not four similar tapes from four suppliers, and one dispenser type, since it affects pack time as much as the tape. See our guide to packing tape grades.
  • Void fill. One primary system per bench, paper or air, with a specified grade. A shorter ladder leaves more void per order, so fill matters more after standardisation, not less.
  • Film. Hand stretch wrap typically runs 17 to 23 micron, pre-stretched 12 to 17 and machine wrap 17 to 30. Hand and machine film are different products, so they cannot be merged, but most sites can drop gauges their loads do not need.
  • Mailers. Cluster mailer sizes the same way; they drift just like boxes.

Roll it out at the bench and measure the result

Rollout

  • Write the ladder down: each step with its internal size, grade and step code, and which products go in it. A written pack specification is how packaging for fulfilment is set up, and it stops the range drifting back.
  • Trial first on one bench or product family, measuring damage, pack time and carrier band together, as in our guide to running a packaging trial.
  • Use up retiring sizes on orders they still fit unless they cause damage, and stop reordering them.
  • Update pack station prompts on the day the bench changes.
  • Change the supply pattern. Fewer lines in larger quantities suits buying the economic run and calling it off through packaging stockholding, rather than filling your racking with board.

Bench layout

Present boxes in ladder order, smallest to largest, with the most-used steps nearest the packer and every slot labelled with its step code; one size per slot. Keep the fill dispenser and tape gun in fixed positions so every bench works the same way.

Measuring the result

MeasureWhat it showsWhere it comes from
Active box linesWhether the range stays standardPurchasing
Orders per sizeWhether each step earns its placePack station
Fill ratio by stepHow much air each step carriesRequired volume against box volume
Void fill per orderWhat the shorter ladder costs in fillFill used against orders
Carrier band mix and surchargesWhether parcels moved into dearer bandsCarrier invoices
Pack time per orderWhether the bench is fasterTimed sample before and after
Damage per thousand despatchesWhether protection held upClaims and returns
Wrong-box picks and stock-outsWhether bench and supply workBench log, emergency orders

Baseline every measure before the change and compare like-for-like periods afterwards. A range that saves board but raises the carrier bill or damage rate has saved nothing. Repeat the order analysis at least yearly, and whenever products or carriers change.

Have your box range checked against your orders

Send us your order data, product dimensions and the carriers you use. We will cluster the orders, propose a standard range with tape, fill and film to match, and say plainly where an existing size should stay.

Frequently asked questions

How many box sizes should a business stock?

There is no right number in general. It depends on how varied your products are, how orders combine and how your carriers price. The right range is the one with the lowest delivered cost against your actual orders, found by testing what each removed size would cost in void fill and carriage.

What is a box ladder?

A box ladder is the set of box sizes you hold, arranged in steps so each step covers a band of orders. It is built from order and dimension data and written into the pack specification, so packers choose the same box for the same order every time.

Will fewer box sizes increase shipping costs?

It can. Orders from a removed size move into a larger box, and carriers that charge on volumetric weight bill the extra space. That is why each removal should be priced against the extra carriage and fill before the size is dropped.

What data do I need to standardise packaging?

Order lines for a representative period including a peak, product dimensions and weights with the protection each needs, current box usage by size, and the carrier bands you use. If full data is not available, start with the products behind most of your orders.

Should tape and void fill be standardised as well?

Yes. Most benches need one general tape grade plus a specified exception, one primary void fill system and only the film grades their loads use. Fill matters more after a box range is shortened, because there is more space to fill per order.

What should we do with box sizes we are dropping?

Stop reordering them and use the remaining stock on orders it still fits, unless the box is causing damage. Update pack station prompts at the same time so retired sizes are no longer suggested.

Related Articles

Freight
Choosing the Right Freight Mode: A Framework for UK Shippers
Air, sea or road? A practical decision framework for balancing cost, speed and reliability.
Freight
FCL vs LCL: Which Container Shipping Option Saves You Money?
Full vs shared containers explained — the break-even point most importers get wrong.
Freight
Road Freight to Europe: What UK Exporters Need to Know
Customs, documentation and transit times for post-Brexit European road freight.

Get a Packaging Quote

Tell us what you pack, how it travels and roughly what volumes, and we will specify it and quote against that specification.