Packaging Materials

Shrink Wrap vs Stretch Film: Which Does Your Pallet Need?

11 min read 22 Nov 2026 WSUK Team
Two warehouse pallets side by side, one wrapped in clear stretch film and one covered with a tight heat-shrunk polythene hood
The quick answer

Stretch film is applied cold and holds a pallet together through elastic recovery; shrink wrap goes on loose and is heated so it contracts around the load. Use stretch film to unitise a pallet for transit. Use shrink film to contain a group of items, make a multipack tamper-evident or weatherproof a load.

The difference between shrink wrap and stretch film

On the shelf of a stores cage, stretch film and shrink wrap look almost identical: clear, thin, polyethylene-family film on a roll. The names get swapped freely on purchase orders, but the two hold a load in opposite ways and do completely different jobs.

Stretch film: cold and elastic

Stretch film is pulled as it is applied, by hand or by a wrapping machine, so there is more of it on the pallet than its unstretched length on the roll. Like a stretched elastic band, it keeps trying to recover, and that recovery is what holds the load. The tension is continuous: as the pallet settles or flexes on a trailer, the film keeps pulling the layers together. No heat is involved, and the film clings to itself so the tail stays put without tape.

Shrink film: loose, then heated

Shrink film goes on loose, as a sleeve, a bag or a hood pulled over the load, and is then heated with a heat gun or passed through a heat tunnel. The heat makes the film contract tightly around the shape of whatever is inside. Once cool it is firm and closely fitted, and on a pallet hood the film is drawn in around the base so the load is held to the pallet as well as covered.

Put simply, stretch film works through the tension it carries and shrink film works through the shape it takes. That one difference explains most of where each belongs.

Which job each film does

Stretch film unitises a pallet so it behaves as one object. That is its whole purpose, and it is the right answer for most palletised despatch: mixed cartons, cases, sacks, anything that needs to stay square and together between the dock and the delivery point. A load that shifts in transit generates far more force than a drop does, which is why under-wrapping shows up as damaged goods rather than as an obvious wrapping fault.

Shrink film contains a group of items. It bundles products into a single unit, makes a multipack tamper-evident, gives retail goods a clean fitted finish and, in heavier gauges, weatherproofs a palletised load with a hood over the top and sides.

RequirementStretch filmShrink film
Unitise a pallet of cartons for UK distributionFirst choiceRarely needed
Bundle small items into one unitPossible with bundling filmFirst choice, in polyolefin
Tamper-evident multipackNot suitedSuited
Weatherproof a pallet stored outsidePartial, with a top coverHeavy polythene shrink hood
How it is appliedCold, by hand or machineHeated, by gun or tunnel
Equipment neededNone for hand wrap; a wrapper for machine filmA heat source, and a sealer for products

For most warehouses the choice is not either-or. Stretch film handles day-to-day pallet despatch, and shrink film comes in for specific lines such as product bundling or pallets that sit outside. If every pallet is shrink-hooded by default, check whether stretch wrap plus a pallet top cover would do the job for less. Both are part of our standard packaging supplies range.

Pallet wrap types and gauges

Film is specified by gauge, width and application method, and each type has its own gauge range. The figures below are common trade gauges, taken from our guide to packaging materials and how each is specified. Hand and machine stretch film come in 400 and 500 mm widths; shrink film is made to order.

FilmTypical gaugeApplied byJob it does
Hand stretch wrap17-23 micronHand, cored rollUnitise a pallet
Pre-stretched hand wrap12-17 micronHandLess film, same hold
Machine stretch wrap17-30 micronWrapping machineConsistent, high volume
Polyolefin shrink film15-25 micronHeat tunnel or gunContain a group
Polythene shrink film30-100 micronHeat tunnel or gunPallet weatherproofing

Hand and machine film are not interchangeable

Machine stretch film and hand stretch film are different products, not grades of the same one. Machine film is made to be stretched by a powered carriage, so applied by hand it will not reach its intended stretch or hold, and you are paying for film that is doing a fraction of its job. If the aim is less plastic on each pallet when wrapping by hand, pre-stretched film is the route: it has been stretched before it reaches you, so a thinner film gives the same hold with less material.

Polyolefin or polythene shrink

Polyolefin shrink film is thin and clear and used mainly on products: bundling, multipacks and retail presentation, typically through a sealer and tunnel. Polythene shrink film is much heavier and used on pallets, usually as a hood or sleeve shrunk with a hand-held heat gun to weatherproof and secure the load.

Equipment, cost and safety

Stretch film has the lowest barrier to entry. Hand wrap needs nothing more than the roll, or a simple dispenser that saves wrists and keeps tension even. Machine wrap needs a turntable or wrapping machine, which earns its place where volumes are high and consistency matters, because it applies the same pattern and tension to every pallet.

Shrink film always needs a heat source, which means equipment, energy and an extra step in the process. For products that is a sealer to close the film and a tunnel to shrink it; for pallets it is usually a heat gun. A shrink hood is a single layer but a much heavier gauge, so do not assume it uses less film than wrapping. Compare the delivered cost per pallet across film, labour, equipment and damage rather than the price per roll. If film spend keeps rising without an obvious reason, it is one of the first things a packaging review looks at.

Heat gun safety, in principle

Shrink guns used on pallets are often gas-fired and produce a flame or very high heat at the nozzle. They belong in a controlled area away from flammable stock, cardboard waste and other combustibles, with gas cylinders stored and checked as the manufacturer directs. Operators should be trained, the task covered by your own risk assessment, and a lit gun never left unattended. Some goods, including flammable or heat-sensitive products, should not be shrunk with a flame at all. If that sounds like a lot of process for a simple job, stretch wrap is usually the better fit.

Recyclability and film waste

Both films are typically polyethylene-family materials. Stretch film is usually linear low-density polyethylene, polythene shrink film is low-density polyethylene, and polyolefin shrink film is often a blend within the same family. Neither has an obvious advantage on material type alone. What decides whether used film is actually recycled is whether it is collected clean, dry and separate from other waste, and whether your waste contractor takes it.

The most dependable improvement is using less: pre-stretched film for hand wrapping, correct tension on machine wrappers, and no shrink hoods on pallets that only need stretch wrap and a top cover. Our sustainable packaging page covers the wider choices.

Stretch film holds a load by tension and shrink film holds it by shape, so buy for the job rather than the finish.

Get the film matched to the load

Tell us the pallet dimensions and weight, whether you wrap by hand or machine, how many rolls you use a week and how the load travels, and we will specify the film and quote the delivered cost.

Frequently asked questions

What is the difference between shrink wrap and stretch film?

Stretch film is stretched cold as it is applied and holds the load by trying to recover its length. Shrink wrap is applied loose and heated so it contracts tightly around the load. Stretch film unitises pallets; shrink film contains groups of items or weatherproofs a load.

Can I use shrink film instead of pallet wrap?

It can secure a pallet, usually as a heavy polythene hood, but it needs a heat source, an extra process step and heavier film. For everyday pallet despatch, stretch wrap is normally the simpler and cheaper choice.

Can machine stretch film be used by hand?

No. Machine and hand stretch film are different products, and machine film applied by hand will not reach its intended stretch or hold. Pre-stretched hand film is the way to use less material when wrapping by hand.

What gauge of stretch film do I need?

Typical trade gauges are 17-23 micron for hand wrap, 12-17 micron for pre-stretched hand wrap and 17-30 micron for machine wrap. The right one depends on the pallet weight, how stable the load is and how it travels.

Do I need special equipment for shrink wrap?

Yes. Shrink film needs heat: a heat gun for pallets, or a sealer and heat tunnel for products. Gas heat guns need trained operators, a controlled area and your own risk assessment.

Are stretch film and shrink film recyclable?

Both are typically polyethylene-family films, so neither has a clear advantage on material alone. Whether they are actually recycled depends on collecting them clean and separate and on your waste contractor accepting them.

Related Articles

Freight
Choosing the Right Freight Mode: A Framework for UK Shippers
Air, sea or road? A practical decision framework for balancing cost, speed and reliability.
Freight
FCL vs LCL: Which Container Shipping Option Saves You Money?
Full vs shared containers explained — the break-even point most importers get wrong.
Freight
Road Freight to Europe: What UK Exporters Need to Know
Customs, documentation and transit times for post-Brexit European road freight.

Get a Packaging Quote

Tell us what you pack, how it travels and roughly what volumes, and we will specify it and quote against that specification.